treble gilt-extra rich

[Deleted member 161536]

WHAT DOES EXTRA RICH MEAN?

 

Amazon Forum Fav 👍

Minelab PRO-FIND 35 Waterproof Pinpointer Metal Detector for Experts with Tone ID & Adjustable Sensitivity - Grab it through Amazon!

[Red-Coat]

Welcome to Tnet. You've posted in the section for people needing technical assistance with the website but, no matter, and the Mods will probably move your post to a mare appropriate section.

Gilt buttons became fashionable in Britain in the mid-to-late 1790s, with the gilding achieved using a closely-guarded process that coated then with an amalgam of mercury and gold (electro-plating didn’t appear until the 1840s). The term ‘gilt’ was sometimes misleadingly used to describe a golden-colour finish with little or no actual gold used, often so poor that the colour would disappear within a few weeks of wear. Some of the gold-coloured lacquers would also fade when exposed to sunlight.

These malpractices led to legislation in Britain in 1796 to inhibit the less ethical makers, with the approved minimum amount of gold for a button to be called “gilt” being set at 1/96th of an ounce per gross of 1 inch buttons. The terms “double gilt” and “treble/triple gilt” were intended to apply to consequent multiples of that amount for superior finishes. Manufacturers took to using terms such as “rich”, “extra-rich”, “extra-fine”, “extra-strong” and also “orange” to circumvent the legislation and/or promote the quality of their buttons (with varying degrees of honesty).

Indented backmarks (like yours) began appearing around 1810 and the previously-used raised backmarks aren’t usually seen after about 1840. During the early 1800s the process details for gilding ‘leaked’ to American producers. Unless a maker name is part of the backmark or there are other identification details, it isn’t usually possible to distinguish American buttons from British ones, except when the word “colour” appears with its British spelling.

 

[Deleted member 161536]

Welcome to Tnet. You've posted in the section for people needing technical assistance with the website but, no matter, and the Mods will probably move your post to a mare appropriate section.

Gilt buttons became fashionable in Britain in the mid-to-late 1790s, with the gilding achieved using a closely-guarded process that coated then with an amalgam of mercury and gold (electro-plating didn’t appear until the 1840s). The term ‘gilt’ was sometimes misleadingly used to describe a golden-colour finish with little or no actual gold used, often so poor that the colour would disappear within a few weeks of wear. Some of the gold-coloured lacquers would also fade when exposed to sunlight.

These malpractices led to legislation in Britain in 1796 to inhibit the less ethical makers, with the approved minimum amount of gold for a button to be called “gilt” being set at 1/96th of an ounce per gross of 1 inch buttons. The terms “double gilt” and “treble/triple gilt” were intended to apply to consequent multiples of that amount for superior finishes. Manufacturers took to using terms such as “rich”, “extra-rich”, “extra-fine”, “extra-strong” and also “orange” to circumvent the legislation and/or promote the quality of their buttons (with varying degrees of honesty).

Indented backmarks (like yours) began appearing around 1810 and the previously-used raised backmarks aren’t usually seen after about 1840. During the early 1800s the process details for gilding ‘leaked’ to American producers. Unless a maker name is part of the backmark or there are other identification details, it isn’t usually possible to distinguish American buttons from British ones, except when the word “colour” appears with its British spelling.

Thank you for your informations!
Here are some pictures. You can see some gold shining on the edge.

 

[Deleted member 161536]

Welcome to Tnet. You've posted in the section for people needing technical assistance with the website but, no matter, and the Mods will probably move your post to a mare appropriate section.

Gilt buttons became fashionable in Britain in the mid-to-late 1790s, with the gilding achieved using a closely-guarded process that coated then with an amalgam of mercury and gold (electro-plating didn’t appear until the 1840s). The term ‘gilt’ was sometimes misleadingly used to describe a golden-colour finish with little or no actual gold used, often so poor that the colour would disappear within a few weeks of wear. Some of the gold-coloured lacquers would also fade when exposed to sunlight.

These malpractices led to legislation in Britain in 1796 to inhibit the less ethical makers, with the approved minimum amount of gold for a button to be called “gilt” being set at 1/96th of an ounce per gross of 1 inch buttons. The terms “double gilt” and “treble/triple gilt” were intended to apply to consequent multiples of that amount for superior finishes. Manufacturers took to using terms such as “rich”, “extra-rich”, “extra-fine”, “extra-strong” and also “orange” to circumvent the legislation and/or promote the quality of their buttons (with varying degrees of honesty).

Indented backmarks (like yours) began appearing around 1810 and the previously-used raised backmarks aren’t usually seen after about 1840. During the early 1800s the process details for gilding ‘leaked’ to American producers. Unless a maker name is part of the backmark or there are other identification details, it isn’t usually possible to distinguish American buttons from British ones, except when the word “colour” appears with its British spelling.

 

[vpnavy]

WHAT DOES EXTRA RICH MEAN?

I moved ya from HELP! over to WHAT IS IT? for more exposure.

NOTE: Forum HELP! contains guides tutorials on how to use the new TreasureNet.com software.