Best deepseeking setting(DFX)

[washingtonian]

I have a Whites DFX and I feel like a have searched a certain field very well and only come away with a few wheat and clad. I have a really good feeling that silver is there, and I was wondering which settings helped to find the deepest coins. As of right now I am just using the pre-made coin setting. Thanks

-Washingtonian

 

Amazon Forum Fav 👍

A Handbook of Civil War Bullets and Cartridges - Grab it through Amazon!

[Sandman]

You deepest setting is always All Metal with no disc. If the field was hunted before, remember silver is very conductive and even a high disc setting will let silver sound off even if deep. All you can hope for then is the other guy didn't over lap his sweeps as much as you and missed some silver.

Good Luck,
Sandman

 

[Schrecky]

The "canned" programs are setup by Whites with conservative settings so that the new user is less likely to run into problems. Your best bet would be to increase the AC Sensitivity to, maybe 72 and your Preamp to 3. Once set, if you hold the coil in the air and are not picking up noise or EMI signals on the display you may be able to increase the Preamp to 4. That should help a lot with depth.

There is a great book out there that covers every detail of the DFX, "Digging Deeper with the DFX" by Jeff Foster. It is pretty technical but explains everything from the settings to ground mineralization. I recommend you get one.

You may also look for advice from the good people at www.dfxonly.com

 

[Eu_citzen]

Here's a program I'm working on:
Target Volume 48 [User preference]
Audio Threshold 17 [User preference]
Tone (Audio Freq) 247 [Good targets get a higher pitch]
Audio Discrim ON
Silent Search OFF
Mixed Mode ON
A.C. Sensitivity 78 [SET FOR STABLE OPERATION]
D.C. Sensitivity 50 [SET FOR STABLE OPERATION]
Backlight OFF
Viewing Angle 25

Pro Options: Audio

Ratchet Pin-pointing OFF
S.A.T Speed 6
Tone I.D ON [Needs to be on for better iron ID, listen for good targets they are high pitched]
V.C.O ON
Modulation OFF

G.E.B /Trac

Autotrac ON
Trac View OFF
Autotrac Speed 8
Autotrac Offset +1
Trac Inhibit ON
Coarse G.E.B AUTO
Fine G.E.B AUTO

Descrim Edit

Accept: -95 to 0
Reject:+1 to +95
Block Edit AS EDIT
Learn Accept OFF
Learn Reject OFF
Recovery Speed 30 [Set as high as high as needed for trash]
Bottlecap Reject 1
Hot Rock Reject 1-6 [If you've got problems with hot rocks turn it up]
Sweep Speed 1
Ground Filtering 3 [Depends on trash and mineralization]

Display

Visual Disc OFF
Icons OFF
V.D.I Sensitivity 85
D.C Phase ON
Graph Averaging ON
Graph Accumulating ON
Fade Rate 7

Single Transmit Receive

Preamp Gain 3 [SET FOR STABLE OPERATION]
2 Frequency (best data) OFF
2 Frequency (correlate) OFF
V.D.I Normalized ON
1 Frequency (3 khz) OFF
1 Frequency (15 khz) ON [If very problematic to get stable try correlate or 3Khz for coins]

It has been posted at DFXonly I also have some other programs there.

 

[eathabs]

As Shrecky said the Digging Deeper With the DFX by Jeff Foster is great. Also, try this link: http://www.whiteselectronics.com/dfxbook.php

I tried to get the free Understanding the DFX book by Jimmy Sierra and it worked. That was back in January, last person to post that they got one was in March. Give it a shot. In the mean time check out the dfxonly.com forum.

Hal

 

[DFX-SE Gregg]

Eu citizen.... I think you have your accept and reject settings backwards!!! You have reject +1 to +95? And accept...-95 to 0? You may want to modify your post...appears 100% backwards...just not to confuse a new dfx user...

 

[Eu_citzen]

No Gregg that is correct, known as reverse discrimination. Also note:

Visual Disc OFF

It WILL show all targets that the Disc mode can get a hold on!

And with Tone ID on and tone at 247 the good targets sound lovely with that high pitched tone!

 

[DFX-SE Gregg]

No Gregg that is correct, known as reverse discrimination. Also note:

Visual Disc OFF

It WILL show all targets that the Disc mode can get a hold on!

And with Tone ID on and tone at 247 the good targets sound lovely with that high pitched tone!

I understand what you are doing... This program is actually a Jeff Foster program slightly modified.. Nothing new...on page 65 of his book..But a few questions for you... Just never heard of it being or working in a single frequency mode... The only way I have heard this program working is in multi frequency...using normally best data on...or correlate...

 

[Eu_citzen]

You are correct Gregg.
It does work with both multi Freq and single freq. That is as long as your not on the salt water beach.

I use it on inland beaches and it works lovely though in some places you need a multi frequency method.