Thompson DW 12V motor and controller...?

[Vorra65]

Hoping someone can help identify the 12V motor and controller for my recently acquired DW.
The controller is the off/variable type, and is completely inop.
I’d have no issue with replacing with the low/off/high box if that’s all I can get. The 12V motor has a spiral splined shaft, that utilizes an 2 eared aluminum bracket for mounting.
Where to get these parts, any leads would be greatly appreciated.

 

Amazon Forum Fav 👍

Minelab PRO-FIND 35 Waterproof Pinpointer Metal Detector for Experts with Tone ID & Adjustable Sensitivity - Grab it through Amazon!

[Jim in Idaho]

A good closeup pic would help.
Jim

 

[Vorra65]

Thanks Jim,
The motor has some #s on it but a few are rubbed and no help-

 

[Vorra65]

 

[Jim in Idaho]

If you can't ind the exact setup, you can probably rig something up. First off, you need the RPM output of the motor, at top speed. Just count the pulses in 10 seconds and multiply by 6. Having that info will allow you to research worm-drive gearmotors. You might be able to find that exact motor, or one that is close enough to work. But, the problem may be with the speed controller. Only way to determine that is to supply the motor with 12v direct, bypassing the speed controller. if it runs, the problem is the controller. if it doesn't the problem is the motor. PWM speed controllers are dirt cheap on EBay. Since yours isn't working, you may need to find someone with a working unit, to tell you the pulses/minute.
Jim

 

[Vorra65]

Reed, the motor works.....just one speed. Was just lookin to get a backup, just in case this one goes south. If I can't find one just like it, if and when it fails I'll just start from scratch and fabricate up an easily accesible popular motor. At that time I'd rework the link to small heim joints on the ends just to get the full throw on the bellows. The 1/4 grizzly is something that will be added as well.

 

[Reed Lukens]

I picked up one of these for my different set ups. I'll bet if you take that motor into a good auto parts store that they can match that motor up in a few minutes.
https://www.amazon.com/gp/product/B081NBRR8Z/?tag=treasurenet01-20

 

[Jim in Idaho]

That's a pretty nice unit, Reed, but I'd want one with at least 10 amp capacity. At 12v 5amps is only 60 watts.
Jim

 

[Reed Lukens]

This is overkill for the bucket sluice that I'm building Jim. Its for a 600gph pump being ran by a small 3ah LiPo4 battery that runs on 3 amps max.

 

[Jim in Idaho]

Form that purpose, it's fine, but probably wouldn't handle the current draw for the drywasher. I just didn't want the OP to buy it thinking it would do the job. The gearmotor I use on the Sweep Jig draws about 5 amps, or a little more under some conditions. I think one reason the motor on the drywasher is getting hot is it's trying to draw more current than the battery can supply, thus lowering the voltage. Low RPM's on motors causes more current through the windings, and a lot of extra heat.
Also, from what I've experienced, most of these Chinese PWM controllers have way overstated current capabilities. Better to go big than go home...LOL
Jim

 

[Vorra65]

Been a bit since I’ve been in the neighborhood. Dug my DW out and did some much needed repairs. After finally finding the exact speed controller that Bill used, thought I’d search out the motor just to have a backup.

Found the controller on Amazon-
The motor fits so many applications, still looking for the most economical vendor to purchase from. Anyway, it’s good to be back…among friends and getting smarter.

 

[Vorra65]

Been a bit since I’ve been in the neighborhood. Dug my DW out and did some much needed repairs. After finally finding the exact speed controller that Bill used, thought I’d search out the motor just to have a backup.

Found the controller on Amazon-
The motor fits so many applications, still looking for the most economical vendor to purchase from. Anyway, it’s good to be back…among friends and getting smarter.

Any of you, or know of anyone lookin….
Selling my Thompson dry washer. Put the new speed controller on it and added a heim joint turnbuckle to the puffer linkage. Have just decided, for where I live and all the dumbass regulations that CA has put in place, I’ll probably never see any frequent use out of it. Will post it in the for sale section soon.

 

[Rte592]

Any of you, or know of anyone lookin….
Selling my Thompson dry washer. Put the new speed controller on it and added a heim joint turnbuckle to the puffer linkage. Have just decided, for where I live and all the dumbass regulations that CA has put in place, I’ll probably never see any frequent use out of it. Will post it in the for sale section soon.

I know someone who is looking for a Thompson puffer Drywasher if you still have it.
Thanks, Rick