Skippy SH13
Bronze Member
- Joined
- Feb 18, 2015
- Messages
- 1,131
- Reaction score
- 2,376
- Golden Thread
- 0
- Primary Interest:
- Metal Detecting
All...
EDIT: THIS OFFER IS NOW at $8, if you want 3 protectors through T-NET. Due to the cost of shipping, and the product, I was losing money on each one I sent out at $5. I expected that, though, which is why it was a limited offer at the $5 price for T-Net folks.
eBay link for $9, if you prefer to purchase there...http://www.ebay.com/itm/-/112241454123? (International folks, this is where you should make the purchase, as eBay facilitates the shipping internationally).
Cheers,
Skippy
I contacted a manufacturer and had 100 of these made to my specifications.
They are 1.5" long and are 0.06" thick (60 mils). They are VERY durable. I've been using a slightly smaller, 1-inch one, on my pin pointer for the last 4 months. I decided a little longer was better, as it covers the blade better. The one I trial tested shows almost NO wear at all, even after thoroughly using it. I even "dig" more confidently with the tip in the dirt. I did notice, though, over time, the softness/pliability of the vinyl tends to harden and take on the shape of the pin pointer (not an issue, but something to be aware of if you take it off and put it back on again... it's normal for the material).
The cost for T-Netters is only $8 for THREE of them, shipping included. This will be BY FAR the least expensive set of pin pointer protectors you'll probably be able to purchase commercially. They are only guaranteed to fit the Pro Pointer, Pro Pointer II, and Garrett Pro Pointer AT (Carrot). The best fit will be on a new device, as worn tips may result in a slight gap at the end. I don't expect problems, though, because the product can be pressed snugly against the end during install.
It's quite likely, you may never have to purchase another pin pointer protector set. I'd be surprised if you ever make it through 2 of them! ... and only for $8! Cheaper than "dipping" or buying protectors commercially.
This deal is for USA folks only (USA/APO), as I'll be shipping first class US Mail. If you are international, please use the eBay link above.
PM me a request with your e-mail address, and I'll send back a Paypal request for the $8. Please pay for it as a good or service (not a gift). This will enable me to print your shipping address and ensures you automatically get a tracking number of the shipment. It also speeds things up, in case I don't have stamps at the house! I will print and ship as soon as I get the payment (because your address will be included through Paypal).
Merry Christmas!
Skippy
EDIT: In case you missed it, please send me a Private Message, if you would like one of these (responding to the thread is more dangerous, since it's possible someone could reply to you with a bogus account info...) To send me a Private Message, click the Skippy SH13 name to the left of my post, and click "Private Message" (Like you see in the below image)., and then send me your e-mail address to where I can send the $8 request.
Cheers!
Skippy
EDIT: THIS OFFER IS NOW at $8, if you want 3 protectors through T-NET. Due to the cost of shipping, and the product, I was losing money on each one I sent out at $5. I expected that, though, which is why it was a limited offer at the $5 price for T-Net folks.
eBay link for $9, if you prefer to purchase there...http://www.ebay.com/itm/-/112241454123? (International folks, this is where you should make the purchase, as eBay facilitates the shipping internationally).
Cheers,
Skippy
I contacted a manufacturer and had 100 of these made to my specifications.
They are 1.5" long and are 0.06" thick (60 mils). They are VERY durable. I've been using a slightly smaller, 1-inch one, on my pin pointer for the last 4 months. I decided a little longer was better, as it covers the blade better. The one I trial tested shows almost NO wear at all, even after thoroughly using it. I even "dig" more confidently with the tip in the dirt. I did notice, though, over time, the softness/pliability of the vinyl tends to harden and take on the shape of the pin pointer (not an issue, but something to be aware of if you take it off and put it back on again... it's normal for the material).
The cost for T-Netters is only $8 for THREE of them, shipping included. This will be BY FAR the least expensive set of pin pointer protectors you'll probably be able to purchase commercially. They are only guaranteed to fit the Pro Pointer, Pro Pointer II, and Garrett Pro Pointer AT (Carrot). The best fit will be on a new device, as worn tips may result in a slight gap at the end. I don't expect problems, though, because the product can be pressed snugly against the end during install.
It's quite likely, you may never have to purchase another pin pointer protector set. I'd be surprised if you ever make it through 2 of them! ... and only for $8! Cheaper than "dipping" or buying protectors commercially.
This deal is for USA folks only (USA/APO), as I'll be shipping first class US Mail. If you are international, please use the eBay link above.
PM me a request with your e-mail address, and I'll send back a Paypal request for the $8. Please pay for it as a good or service (not a gift). This will enable me to print your shipping address and ensures you automatically get a tracking number of the shipment. It also speeds things up, in case I don't have stamps at the house! I will print and ship as soon as I get the payment (because your address will be included through Paypal).
Merry Christmas!
Skippy
EDIT: In case you missed it, please send me a Private Message, if you would like one of these (responding to the thread is more dangerous, since it's possible someone could reply to you with a bogus account info...) To send me a Private Message, click the Skippy SH13 name to the left of my post, and click "Private Message" (Like you see in the below image)., and then send me your e-mail address to where I can send the $8 request.
Cheers!
Skippy
Amazon Forum Fav 👍
Last edited:
As an eBay Associate we earn from qualifying purchases.
Upvote
0
I'm already considering adding another .5 inches to the protector, to allow more "wand digging" without getting junk under the cap. Colors are out, too, as I have to buy in bulk. Anything else, though is fair game!
