excal2 users .... jus quick ?

[BOBBY PIN KING]

Normally I never ask for help but this is bothering me, bhid did better today than new excal2 on wet sand stable, in water stable, but from water back to sand even after adjusting sens, a lot of falsing and tone changing, when swingin, and or touching sand with cover , tried pin point,disc, changing sensitivity, wire isn't flooping around, didn't get unit wet,dry batt terminals drove me nuts,,,,,the ear muffs SUCK...but I didn't dig any bobby pins.. that's the only thing that kept me sorta sain....? works great before wet,,,,,,solution

 

Amazon Forum Fav 👍

How to Research for Treasure Hunting and Metal Detecting From Lead Generation to Vetting - Grab it through Amazon!

[cdv1]

Is there someone close by that is an Excal user that can see your unit in action? That could be the quickest way to determine if the unit is ok. To me it sounds like you could have a coil problem.... OR you have some adjustments on the pots that aren't quite right.

Cliff

 

[zigzag]

I can't help you on the falsing problem but gel seals will make the headphones much more comfortable.

 

[njal]

Is this a new machine?

Maybe Dr. OBN will see your post.

 

[Jason in Enid]

Sounds like water problem. If there is a cut or crack anywhere in the coil cable, you will get water going down into the coil and even up into the controls so I would start by checking that first.

 

[Treasure_Hunter]

More info would help, what were your settings on the excal?
Do you have a coil cover on?
How is the battery charge, a battery that is close to uncharged will act just like that, have you checked the battery to see if it is holding a full charge?

 

[Treasure_Hunter]

Bobby, you and I live very close together, I live in Orlando very close to Apopka, I see your close to Eutis..... If you want I can check it out for you....

 

[Treasure_Hunter]

If your swinging the coil in very shallow water you will get falsing as the waves roll over it also...... Just a thought....

 

[mham2]

check under coil cover ,sand in there will cause it to false

 

[tnt-k9]

Not an Ex-Cal expert as I use mine as a back-up machine. Too many tones. Check your coil, make sure there is no debris in the coil cover. Turn the sensitivity down. Good luck.

 

[BOBBY PIN KING]

Jus checked coil cover....sand....awesome... drying now...gonna use small bead of silicon...to seal out sand and water.....thanks...will post results.........will reply to PM's shortly after "ol lady". Cools off......she out a cigs...lol

 

[Treasure_Hunter]

Jus checked coil cover....sand....awesome... drying now...gonna use small bead of silicon...to seal out sand and water.....thanks...will post results.........will reply to PM's shortly after "ol lady". Cools off......she out a cigs...lol

If your hunting salt beaches and water you don't need the cover, I haven't used one in water in 6 years

Sent from my Galaxy Nexus using Tapatalk 2

 

[surfnturf]

No cover for me!! maybe some truck bed liner spray!


SnT

Kinda like a jimmy hat!

 

[OBN]

Is this a new machine?

Maybe Dr. OBN will see your post.

My words exactly, new machine? TH is right, need someone near that has some Excalibur time in to test it...

 

[CSMPEREZ]

I'm going to gamble that you don't have the proper settings. Take Cliffs recommendations and see if there is an experienced EXCAL user in your area that will help you. reading the manual really helps!! Ray

 

[Treasure_Hunter]

I'm going to gamble that you don't have the proper settings. Take Cliffs recommendations and see if there is an experienced EXCAL user in your area that will help you. reading the manual really helps!! Ray

He and I live fairly close together I have contacted him and he knows how to reach me if he needs it checked out further....

Sent from my Galaxy Nexus using Tapatalk 2

 

[BOBBY PIN KING]

new machine...sens was,4-6 took off coil cover off , works fine,,, cleaned it up gonna put back on and seal it up, never knew sand between the two could cause so much "fun",,,, may have to change name now

 

[Treasure_Hunter]

new machine...sens was,4-6 took off coil cover off , works fine,,, cleaned it up gonna put back on and seal it up, never knew sand between the two could cause so much "fun",,,, may have to change name now

You know hunting the local beaches here you dont need the coil cover, I have never used one on my excals and in 6 years not wore out a coil or damaged it from using it.... I did crack a coil one day when I made the stupid mistake of standing it coil up against my truck in driveway and it slid down and cracked coil, but that was my error, and not caused by lack of coil cover use....

 

[MiamiFox]

Glad you found the problem, same thing happened to my AT pro when I first got it and haven't used the cover since then.

 

[OBN]

BPK, question for you...I see a boat n fish finder, have you thought about using the fish finder as a tool for detecting