What kind of paint would you choose to cover a coffee table?

[kitt]

I know this isnt the Do It Yourself forum but I know almost every one here is a do it yourselfer. Plus have you ever seen the forum category's?
I need an inexpensive way to make it look nicer because we are a family of 3 on $0.30 over min wage
So i know theres lots of paint like Enamal, Latex, water or oil based and so on. Well my table is very disappointing to look at.
Wheres about 30% of the finish is gone. So either refinish it or paint it and I think painting would be less of a hassle. Which will hold the best?

 

Amazon Forum Fav 👍

A History of Mining on the Kenai Peninsula, Alaska - Grab it through Amazon!

[stefen]

Depends on age, the style, type of wood (or material) and quality of workmanship.

Striping is based on time.

Then again, if you don't give a hoot, then by all means slop some paint on it...ugly becomes uglier.

Once you determine the direction you want to go, then resolve the type of paint to use.

FYI, I just purchased an old oak tool chest that was ugly as they get...almost solid black with 75 years of oil smudges and grime.

Spent a few hours scrubbing it with a dish scrubby and a strong TSP detergent, and out of the grime a quarter=sawn tiger oak box surfaced.

A little danish oil and now have something to be proud of.

Time is the key word....and patients...

 

[Joe hunter]

Sand lightly with fairly fine sand paper 120/ or higher I prefer enamel paints avoid flat paints there not as durable oil cost more is more difficult to work with I prefer a brushed look with sanded corners spray cans are also an option if you got space to spray and good ventilation try not to use spray cans in living space it stinks is harmful to breath and tends get everywhere this is sample of sanded corners on a hutch I did maybe you can zoom to see better good luck

 

[ga/digger]

what joe said
what joe sai

Sand lightly with fairly fine sand paper 120/ or higher I prefer enamel paints avoid flat paints there not as durable oil cost more is more difficult to work with I prefer a brushed look with sanded corners spray cans are also an option if you got space to spray and good ventilation try not to use spray cans in living space it stinks is harmful to breath and tends get everywhereView attachment 1237589this is sample of sanded corners on a hutch I did maybe you can zoom to see better good luck

 

[kitt]

Thanks guys! I went to the hardware store today and got some more info. I told the lady i wanted to do a 2 tone sponge with almond base and sand sponge blotches.
She told me I would need to primer it paint and glaze it. Not sure what this glaze is but she said it was to give the paint a transparency look.
After adding the toll Of $10 a quart for prime, almond paint, sand paint, comes to $30 and no clue the prize of glaze. then factor in sand paper, brushes ect. I could almost buy a great condition used table lolol.

 

[clv]

give it sand job, clean up the dust, go to HD or lowes paint department, you will find a small shelf of "oops" paint. Give it two coats with a sand of 180 to 240 grit in between.

 

[NC Digger]

Thanks guys! I went to the hardware store today and got some more info. I told the lady i wanted to do a 2 tone sponge with almond base and sand sponge blotches.
She told me I would need to primer it paint and glaze it. Not sure what this glaze is but she said it was to give the paint a transparency look.
After adding the toll Of $10 a quart for prime, almond paint, sand paint, comes to $30 and no clue the prize of glaze. then factor in sand paper, brushes ect. I could almost buy a great condition used table lolol.

Do a search on the net for glazing. It would probably be a waste only because your using it as a table. What ever you do, Do Not use latex! Oil based paints hold up better, if you can sand the table to bare wood, stain and then polly it, that would be the best and hardest covering out of anything you could do! Good luck with your project!

 

[Jason in Enid]

I hate paint on wood. I would suggest sanding and applying a tung-oil finish. Formesby has a good one, that is premixed with thinner to speed the drying / curing time. It takes a little longer than slapping on some paint, but wood is beautiful and should be shown.

 

[SusanMN]

Sometimes you just have to paint. I personally like spray paint because I think it finishes harder. So I would give it a couple coats of spray paint, flat non gloss, in maybe an expresso color. Then a light sand and at least three coats of satin polyurathane, sanding lightly and using a tack clothes between each coat. It is a lot of work but once done it will hold up to spills and wet glasses without leaving a mark.

 

[Dr. Syn]

Don't paint wood, you are hiding the beauty of it. Like said you never know what's hiding beneath the surface. I've used Formby's Refinisher on old items before, it does a nice job of blending the old finish and exposing the wood's beauty. And some tongue oil over it when done and you end up with an family treasure.

 

[River Rat]

I totally agree with Jason & Dr. Syn! I love the beauty of wood! The thing now, is the stressed look...some are pretty, some are ugly as h___. I recently refinished a sewing machine bench back to it's natural wood. I had to do a lot of stripping & sanding...had 3 coats of 3 different colors.